Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
They are making a number of great pointers on Tools You Need to Install a New Bathtub in general in this post down below.
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately difficult task. If the old tub is readily obtainable, the job can relocate quickly; if you need to open up a wall surface to eliminate the old tub as well as position the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require an assistant to vacate the old tub and also embeded in the new one. Make sure you have actually certified yourself for the task and fit trying it. Rather than working with a specialist to take over a halfway-completed job, it is much better to think about employing one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This write-up will certainly help you mount a brand-new bathtub in your washroom if you have already gotten a brand-new bathtub as well as do not require to transform the arrangement of your previous water pipes.
Your devices and material list should consist of the following:
Planning for the Installment
First of all, the supporting frame provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to prevent strain on the bath tub.
Fit the adaptable tap adapters to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you must do is separate the water. After doing so, turn on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome due to the restricted accessibility that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will originate from the pipes. When the supply pipelines have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before going on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the level reads degree.
To install taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and likewise inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait till the bath tub has actually been used at the very least when as this will resolve it into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making sure that the washers are in area in between the faucet and also the sink. Secure the tap in place with the supplier given backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type must be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall surface between the bath and the tiling, leading to difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, and also are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealer can split relatively very early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give feedback directly below. We will be pleased to know your views about this posting. We hope that you come back again in the near future. Those who enjoyed our blog post please remember to share it. I am grateful for your time. Visit again soon.
Reliable repairs? Dial. Report this page